mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-11-27 11:06:37 +06:00
80 lines
3.3 KiB
C
80 lines
3.3 KiB
C
/* Copyright 2022 customMK
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
#pragma once
|
|
|
|
#include "config_common.h"
|
|
|
|
// This file includes example #defines to enable commonly-used functionality
|
|
// (SPI, PWM backlight, etc.) on specific pins. Capabilities you want to include
|
|
// should be added to the config.h for your keyboard. Not all capabilities are
|
|
// shown; for example:
|
|
// I2C is not shown because the QMK defaults are sufficient for SCL on B6 and SDA on B7
|
|
// Serial communications (for split keyboards) is not shown because QMK defaults work
|
|
// for either pins A15 or B6
|
|
|
|
// If you need to change pins for PWM, SPI, I2C, or Serial communications, be aware that
|
|
// doing this may require changing the driver, channel, PAL (Pin ALternate function) mode,
|
|
// DMA stream, and/or DMA channel.
|
|
|
|
|
|
// Bonsai C4 wires up pin A9 for Vbus sensing pin by default. For spilt keyboards, this
|
|
// can be used to determine which half of the keyboard is plugged into USB.
|
|
// For boards using Bonsai C4 merely as a reference design, the VBUS sense pin A9
|
|
// can be used for purposes other than Vbus sensing (e.g. the switch
|
|
// matrix).
|
|
//
|
|
// If A9 is needed for Vbus sensing, uncomment the line
|
|
// below. Most keyboards using Bonsai C4 can leave the line below
|
|
// commented out.
|
|
//
|
|
// #undef BOARD_OTG_NOVBUSSENS
|
|
|
|
// FRAM configuration
|
|
#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN A0
|
|
#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR 8 // 96MHz / 8 = 12MHz; max supported by MB85R64 is 20MHz
|
|
#define EXTERNAL_EEPROM_PAGE_SIZE 64 // does not matter for FRAM, just sets the RAM buffer size in STM32F chip
|
|
#define DYNAMIC_KEYMAP_EEPROM_MAX_ADDR 8191
|
|
|
|
// External flash configuration
|
|
#define EXTERNAL_FLASH_SPI_SLAVE_SELECT_PIN B12
|
|
#define EXTERNAL_FLASH_SPI_CLOCK_DIVISOR 1 // 96MHz; max supported by W25Q128JV is 133MHz
|
|
#define EXTERNAL_FLASH_BYTE_COUNT (16 * 1024 * 1024) //128Mbit or 16MByte
|
|
#define EXTERNAL_FLASH_PAGE_SIZE 256
|
|
#define EXTERNAL_FLASH_SPI_TIMEOUT 200000 //datasheet max is 200 seconds for flash chip erase
|
|
|
|
// SPI Configuration (needed for FRAM and FLASH)
|
|
#define SPI_DRIVER SPID1
|
|
#define SPI_SCK_PIN B3
|
|
#define SPI_MOSI_PIN B5
|
|
#define SPI_MISO_PIN B4
|
|
|
|
// Example code to set up PWM backlight on pin A6
|
|
// If a different pin is used, a different PWM driver/channel settings may be necessary
|
|
#define BACKLIGHT_PIN A6
|
|
#define BACKLIGHT_PWM_DRIVER PWMD3
|
|
#define BACKLIGHT_PWM_CHANNEL 1
|
|
|
|
// Example code for WS2812 underglow
|
|
// Only pin A10 is wired to send 5V signals to the WS2812
|
|
// This also usually requires adding special wiring during board assembly
|
|
#define RGB_DI_PIN A10
|
|
#define WS2812_PWM_DRIVER PWMD1
|
|
#define WS2812_PWM_CHANNEL 3
|
|
#define WS2812_PWM_PAL_MODE 1
|
|
#define WS2812_DMA_STREAM STM32_DMA2_STREAM5
|
|
#define WS2812_DMA_CHANNEL 6
|