mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-11-30 04:37:14 +06:00
6e27f6fbde
new file: keyboards/lets_splitv2/Makefile new file: keyboards/lets_splitv2/config.h new file: keyboards/lets_splitv2/i2c.c new file: keyboards/lets_splitv2/i2c.h new file: keyboards/lets_splitv2/imgs/split-keyboard-i2c-schematic.png new file: keyboards/lets_splitv2/imgs/split-keyboard-serial-schematic.png new file: keyboards/lets_splitv2/keymaps/default/keymap.c new file: keyboards/lets_splitv2/lets_split.c new file: keyboards/lets_splitv2/lets_split.h new file: keyboards/lets_splitv2/matrix.c new file: keyboards/lets_splitv2/pro_micro.h new file: keyboards/lets_splitv2/readme.md new file: keyboards/lets_splitv2/serial.c new file: keyboards/lets_splitv2/serial.h new file: keyboards/lets_splitv2/split_util.c new file: keyboards/lets_splitv2/split_util.h new file: keyboards/maxipad/Makefile new file: keyboards/maxipad/config.h new file: keyboards/maxipad/keymaps/default/Makefile new file: keyboards/maxipad/keymaps/default/config.h new file: keyboards/maxipad/keymaps/default/keymap.c new file: keyboards/maxipad/keymaps/default/readme.md new file: keyboards/maxipad/maxipad.c new file: keyboards/maxipad/maxipad.h new file: keyboards/maxipad/readme.md
78 lines
3.1 KiB
Makefile
78 lines
3.1 KiB
Makefile
SRC += matrix.c \
|
|
i2c.c \
|
|
split_util.c \
|
|
serial.c
|
|
|
|
# MCU name
|
|
#MCU = at90usb1287
|
|
MCU = atmega32u4
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU = 16000000
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in *bytes*
|
|
# Teensy halfKay 512
|
|
# Teensy++ halfKay 1024
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
# USBaspLoader 2048
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
# Build Options
|
|
# change to "no" to disable the options, or define them in the Makefile in
|
|
# the appropriate keymap folder that will get included automatically
|
|
#
|
|
BOOTMAGIC_ENABLE ?= no # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE ?= yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE ?= yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE ?= no # Console for debug(+400)
|
|
COMMAND_ENABLE ?= yes # Commands for debug and configuration
|
|
NKRO_ENABLE ?= no # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
|
BACKLIGHT_ENABLE ?= no # Enable keyboard backlight functionality
|
|
MIDI_ENABLE ?= no # MIDI controls
|
|
AUDIO_ENABLE ?= yes # Audio output on port C6
|
|
UNICODE_ENABLE ?= no # Unicode
|
|
BLUETOOTH_ENABLE ?= no # Enable Bluetooth with the Adafruit EZ-Key HID
|
|
RGBLIGHT_ENABLE ?= no # Enable WS2812 RGB underlight. Do not enable this with audio at the same time.
|
|
USE_I2C ?= yes
|
|
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
|
SLEEP_LED_ENABLE ?= no # Breathing sleep LED during USB suspend
|
|
|
|
CUSTOM_MATRIX = yes
|
|
|
|
ifndef QUANTUM_DIR
|
|
include ../../Makefile
|
|
endif |