mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-12-25 10:44:59 +06:00
Fix Makfile and config.h for LUFA in ps2_usb
This commit is contained in:
tmk
parent
4e36159be2
commit
04c9501574
@ -1,5 +1,5 @@
|
||||
# Target file name (without extension).
|
||||
TARGET = ps2_usb
|
||||
TARGET = ps2_usb_lufa
|
||||
|
||||
# Directory common source filess exist
|
||||
TOP_DIR = ../..
|
||||
@ -7,69 +7,96 @@ TOP_DIR = ../..
|
||||
# Directory keyboard dependent files exist
|
||||
TARGET_DIR = .
|
||||
|
||||
|
||||
# MCU name, you MUST set this to match the board you are using
|
||||
# type "make clean" after changing this, so all files will be rebuilt
|
||||
#MCU = at90usb162 # Teensy 1.0
|
||||
MCU = atmega32u4 # Teensy 2.0
|
||||
#MCU = at90usb646 # Teensy++ 1.0
|
||||
#MCU = at90usb1286 # Teensy++ 2.0
|
||||
|
||||
|
||||
# Processor frequency.
|
||||
# Normally the first thing your program should do is set the clock prescaler,
|
||||
# so your program will run at the correct speed. You should also set this
|
||||
# variable to same clock speed. The _delay_ms() macro uses this, and many
|
||||
# examples use this variable to calculate timings. Do not add a "UL" here.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
# Build Options
|
||||
# *Comment out* to disable the options.
|
||||
#
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control
|
||||
NKRO_ENABLE = yes # USB Nkey Rollover
|
||||
|
||||
PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
|
||||
#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
|
||||
#PS2_USE_BUSYWAIT = yes # uses primitive reference code
|
||||
|
||||
|
||||
# keyboard dependent files
|
||||
SRC = keymap.c \
|
||||
# project specific files
|
||||
SRC = keymap_common.c \
|
||||
matrix.c \
|
||||
led.c
|
||||
|
||||
|
||||
ifdef PS2_USE_USART
|
||||
SRC += protocol/ps2_usart.c
|
||||
OPT_DEFS += -DPS2_USE_USART
|
||||
endif
|
||||
ifdef PS2_USE_INT
|
||||
SRC += protocol/ps2.c
|
||||
OPT_DEFS += -DPS2_USE_INT
|
||||
endif
|
||||
ifdef PS2_USE_BUSYWAIT
|
||||
SRC += protocol/ps2.c
|
||||
OPT_DEFS += -DPS2_USE_BUSYWAIT
|
||||
ifdef KEYMAP
|
||||
SRC := keymap_$(KEYMAP).c $(SRC)
|
||||
else
|
||||
SRC := keymap_plain.c $(SRC)
|
||||
endif
|
||||
|
||||
|
||||
#CONFIG_H = config_pjrc_usart.h
|
||||
CONFIG_H = config.h
|
||||
|
||||
|
||||
#---------------- Programming Options --------------------------
|
||||
PROGRAM_CMD = teensy_loader_cli -mmcu=$(MCU) -w -v $(TARGET).hex
|
||||
# MCU name
|
||||
#MCU = at90usb1287
|
||||
MCU = atmega32u4
|
||||
|
||||
# Processor frequency.
|
||||
# This will define a symbol, F_CPU, in all source code files equal to the
|
||||
# processor frequency in Hz. You can then use this symbol in your source code to
|
||||
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||||
# automatically to create a 32-bit value in your source code.
|
||||
#
|
||||
# This will be an integer division of F_USB below, as it is sourced by
|
||||
# F_USB after it has run through any CPU prescalers. Note that this value
|
||||
# does not *change* the processor frequency - it should merely be updated to
|
||||
# reflect the processor speed set externally so that the code can use accurate
|
||||
# software delays.
|
||||
F_CPU = 16000000
|
||||
|
||||
|
||||
#
|
||||
# LUFA specific
|
||||
#
|
||||
# Target architecture (see library "Board Types" documentation).
|
||||
ARCH = AVR8
|
||||
|
||||
# Input clock frequency.
|
||||
# This will define a symbol, F_USB, in all source code files equal to the
|
||||
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||||
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||||
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||||
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||||
# at the end, this will be done automatically to create a 32-bit value in your
|
||||
# source code.
|
||||
#
|
||||
# If no clock division is performed on the input clock inside the AVR (via the
|
||||
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||||
F_USB = $(F_CPU)
|
||||
|
||||
# Interrupt driven control endpoint task(+60)
|
||||
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||||
|
||||
|
||||
# Boot Section Size in *bytes*
|
||||
# Teensy halfKay 512
|
||||
# Teensy++ halfKay 1024
|
||||
# Atmel DFU loader 4096
|
||||
# LUFA bootloader 4096
|
||||
# USBaspLoader 2048
|
||||
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
||||
|
||||
|
||||
# Build Options
|
||||
# comment out to disable the options.
|
||||
#
|
||||
#BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||||
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||||
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||||
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||||
COMMAND_ENABLE = yes # Commands for debug and configuration
|
||||
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
||||
|
||||
|
||||
# PS/2 Options
|
||||
#
|
||||
#PS2_USE_USART = yes # uses hardware USART engine for PS/2 signal receive(recomened)
|
||||
#PS2_USE_INT = yes # uses external interrupt for falling edge of PS/2 clock pin
|
||||
PS2_USE_BUSYWAIT = yes # uses primitive reference code
|
||||
|
||||
|
||||
# Optimize size but this may cause error "relocation truncated to fit"
|
||||
#EXTRALDFLAGS = -Wl,--relax
|
||||
|
||||
# Search Path
|
||||
VPATH += $(TARGET_DIR)
|
||||
VPATH += $(TOP_DIR)
|
||||
|
||||
|
||||
include $(TOP_DIR)/protocol/pjrc.mk
|
||||
include $(TOP_DIR)/protocol.mk
|
||||
include $(TOP_DIR)/protocol/lufa.mk
|
||||
include $(TOP_DIR)/common.mk
|
||||
include $(TOP_DIR)/rules.mk
|
||||
|
||||
@ -22,6 +22,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
||||
#define VENDOR_ID 0xFEED
|
||||
#define PRODUCT_ID 0x6512
|
||||
#define DEVICE_VER 0x0001
|
||||
#define MANUFACTURER t.m.k.
|
||||
#define PRODUCT PS/2 keyboard converter
|
||||
#define DESCRIPTION convert PS/2 keyboard to USB
|
||||
@ -39,10 +40,6 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
)
|
||||
|
||||
|
||||
/* legacy keymap support */
|
||||
#define USE_LEGACY_KEYMAP
|
||||
|
||||
|
||||
#ifdef PS2_USE_USART
|
||||
#if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)
|
||||
/* XCK for clock line and RXD for data line */
|
||||
@ -136,7 +133,7 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 1
|
||||
#define PS2_CLOCK_BIT 5
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
@ -157,14 +154,14 @@ along with this program. If not, see <http://www.gnu.org/licenses/>.
|
||||
|
||||
|
||||
#ifdef PS2_USE_BUSYWAIT
|
||||
#define PS2_CLOCK_PORT PORTF
|
||||
#define PS2_CLOCK_PIN PINF
|
||||
#define PS2_CLOCK_DDR DDRF
|
||||
#define PS2_CLOCK_BIT 0
|
||||
#define PS2_DATA_PORT PORTF
|
||||
#define PS2_DATA_PIN PINF
|
||||
#define PS2_DATA_DDR DDRF
|
||||
#define PS2_DATA_BIT 1
|
||||
#define PS2_CLOCK_PORT PORTD
|
||||
#define PS2_CLOCK_PIN PIND
|
||||
#define PS2_CLOCK_DDR DDRD
|
||||
#define PS2_CLOCK_BIT 5
|
||||
#define PS2_DATA_PORT PORTD
|
||||
#define PS2_DATA_PIN PIND
|
||||
#define PS2_DATA_DDR DDRD
|
||||
#define PS2_DATA_BIT 2
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
Loading…
Reference in New Issue
Block a user