mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-11-24 09:27:36 +06:00
91 lines
3.3 KiB
Markdown
91 lines
3.3 KiB
Markdown
|
# UART Driver
|
||
|
|
|
||
|
|
The UART drivers used in QMK have a set of common functions to allow portability between MCUs.
|
||
|
|
|
||
|
|
Currently, this driver does not support enabling hardware flow control (the `RTS` and `CTS` pins) if available, but may do so in future.
|
||
|
|
|
||
|
|
## AVR Configuration
|
||
|
|
|
||
|
|
No special setup is required - just connect the `RX` and `TX` pins of your UART device to the opposite pins on the MCU:
|
||
|
|
|
||
|
|
|MCU |`TX`|`RX`|`CTS`|`RTS`|
|
||
|
|
|-------------|----|----|-----|-----|
|
||
|
|
|ATmega16/32U2|`D3`|`D2`|`D7` |`D6` |
|
||
|
|
|ATmega16/32U4|`D3`|`D2`|`D5` |`B7` |
|
||
|
|
|AT90USB64/128|`D3`|`D2`|*n/a*|*n/a*|
|
||
|
|
|ATmega32A |`D1`|`D0`|*n/a*|*n/a*|
|
||
|
|
|ATmega328/P |`D1`|`D0`|*n/a*|*n/a*|
|
||
|
|
|
||
|
|
## ChibiOS/ARM Configuration
|
||
|
|
|
||
|
|
You'll need to determine which pins can be used for UART -- as an example, STM32 parts generally have multiple UART peripherals, labeled USART1, USART2, USART3 etc.
|
||
|
|
|
||
|
|
To enable UART, modify your board's `halconf.h` to enable the serial driver:
|
||
|
|
|
||
|
|
```c
|
||
|
|
#define HAL_USE_SERIAL TRUE
|
||
|
|
```
|
||
|
|
|
||
|
|
Then, modify your board's `mcuconf.h` to enable the peripheral you've chosen, for example:
|
||
|
|
|
||
|
|
```c
|
||
|
|
#undef STM32_SERIAL_USE_USART2
|
||
|
|
#define STM32_SERIAL_USE_USART2 TRUE
|
||
|
|
```
|
||
|
|
|
||
|
|
Configuration-wise, you'll need to set up the peripheral as per your MCU's datasheet -- the defaults match the pins for a Proton-C, i.e. STM32F303.
|
||
|
|
|
||
|
|
|`config.h` override |Description |Default Value|
|
||
|
|
|--------------------------|---------------------------------------------------------------|-------------|
|
||
|
|
|`#define SERIAL_DRIVER` |USART peripheral to use - USART1 -> `SD1`, USART2 -> `SD2` etc.|`SD1` |
|
||
|
|
|`#define SD1_TX_PIN` |The pin to use for TX |`A9` |
|
||
|
|
|`#define SD1_TX_PAL_MODE` |The alternate function mode for TX |`7` |
|
||
|
|
|`#define SD1_RX_PIN` |The pin to use for RX |`A10` |
|
||
|
|
|`#define SD1_RX_PAL_MODE` |The alternate function mode for RX |`7` |
|
||
|
|
|`#define SD1_CTS_PIN` |The pin to use for CTS |`A11` |
|
||
|
|
|`#define SD1_CTS_PAL_MODE`|The alternate function mode for CTS |`7` |
|
||
|
|
|`#define SD1_RTS_PIN` |The pin to use for RTS |`A12` |
|
||
|
|
|`#define SD1_RTS_PAL_MODE`|The alternate function mode for RTS |`7` |
|
||
|
|
|
||
|
|
## Functions
|
||
|
|
|
||
|
|
### `void uart_init(uint32_t baud)`
|
||
|
|
|
||
|
|
Initialize the UART driver. This function must be called only once, before any of the below functions can be called.
|
||
|
|
|
||
|
|
#### Arguments
|
||
|
|
|
||
|
|
- `uint32_t baud`
|
||
|
|
The baud rate to transmit and receive at. This may depend on the device you are communicating with. Common values are 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200.
|
||
|
|
|
||
|
|
---
|
||
|
|
|
||
|
|
### `void uart_putchar(uint8_t c)`
|
||
|
|
|
||
|
|
Transmit a single byte.
|
||
|
|
|
||
|
|
#### Arguments
|
||
|
|
|
||
|
|
- `uint8_t c`
|
||
|
|
The byte (character) to send, from 0 to 255.
|
||
|
|
|
||
|
|
---
|
||
|
|
|
||
|
|
### `uint8_t uart_getchar(void)`
|
||
|
|
|
||
|
|
Receive a single byte.
|
||
|
|
|
||
|
|
#### Return Value
|
||
|
|
|
||
|
|
The byte read from the receive buffer.
|
||
|
|
|
||
|
|
---
|
||
|
|
|
||
|
|
### `bool uart_available(void)`
|
||
|
|
|
||
|
|
Return whether the receive buffer contains data. Call this function to determine if `uart_getchar()` will return meaningful data.
|
||
|
|
|
||
|
|
#### Return Value
|
||
|
|
|
||
|
|
`true` if the receive buffer length is non-zero.
|