mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-11-22 16:37:58 +06:00
63 lines
2.9 KiB
Markdown
63 lines
2.9 KiB
Markdown
|
# QMK-based firmware for Zenith Z-150 keyboard
|
|||
|
|
|
|||
|
|
|
|||
|
|
|
|||
|
|
Zenith Z-150 keyboard conversion project: direct connection of Black Pill to the matrix.
|
|||
|
|
|
|||
|
|
* Keyboard Maintainer: [DmNosachev](https://github.com/DmNosachev)
|
|||
|
|
* Hardware Supported: [Zenith Z-150 keyboard, 100-1860 version with white logo](https://deskthority.net/wiki/Zenith_Z-150), Black Pill STM32F103C8T6 MCU board. Alternatevely you can use any MCU which is supported by QMK and has 22 or more IO pins: Arduino Micro, Teensy 2.0, Teensy 2.0++, Blue Pill, etc.
|
|||
|
|
|
|||
|
|
Earlier 100-1886 version with black logo has different PCB.
|
|||
|
|
|
|||
|
|
Make example for this keyboard (after setting up your build environment):
|
|||
|
|
|
|||
|
|
make handwired/z150:default
|
|||
|
|
|
|||
|
|
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
|
|||
|
|
|
|||
|
|
# Modding
|
|||
|
|
|
|||
|
|
## Matrix
|
|||
|
|
|
|||
|
|
Z-150 has 11x8 matrix. It's ghost-free thanks to the diodes.
|
|||
|
|
|
|||
|
|
Columns are located under NEC D8049HC MCU IC:
|
|||
|
|
|
|||
|
|
|
|||
|
|
Rows are connected to unmarked 24-pin MUX IC:
|
|||
|
|
|
|||
|
|
|
|||
|
|
## LEDs
|
|||
|
|
|
|||
|
|
LEDs (from left to right): NumLock, CapsLock, ScrollLock:
|
|||
|
|
|
|||
|
|
|
|||
|
|
Their anodes are connected to VCC through 220Ω resistors.
|
|||
|
|
|
|||
|
|
|
|||
|
|
You can keep the original resistors, but with Black Pill or any other 3.3V controller the LEDs may seem a little dim. Try 150Ω or close value if you want to fix that.
|
|||
|
|
|
|||
|
|
|
|||
|
|
## Black Pill
|
|||
|
|
Suggested mount position for the Black Pill (view from the bottom side of the PCB):
|
|||
|
|
|
|||
|
|
```
|
|||
|
|
R0 R1 R2 R3 R4 R6 R9 LC LN LS
|
|||
|
|
,--------------------------------------------------------------------,
|
|||
|
|
|B12 B13 B14 B15 A8 A9 A10 A11 A12 A15 B3 B4 B5 B6 B7 3V3 GND |---,
|
|||
|
|
| |USB|
|
|||
|
|
|B11 B10 B1 B0 A7 A6 A5 A4 A3 A2 A1 A0 RST C13 B9 B8 GND |---'
|
|||
|
|
'--------------------------------------------------------------------'
|
|||
|
|
C0 C1 C2 C3 C4 C5 C6 C7 R5 R8 R7 RA
|
|||
|
|
```
|
|||
|
|
|
|||
|
|
|
|||
|
|
1. Desolder all ICs, crystal oscillator, capacitors and resistors except R0–R2 (they connect LEDs to VCC).
|
|||
|
|
1. Solder 12-pin header to the Black Pill (pins B11–A0 on the left side).
|
|||
|
|
2. Solder two 3-pin headers for boot jumpers.
|
|||
|
|
3. Solder 4-pin SWD header.
|
|||
|
|
4. Burn [STM32duino bootloader](https://github.com/rogerclarkmelbourne/STM32duino-bootloader/blob/master/bootloader_only_binaries/generic_boot20_pb12.bin) to Black Pill.
|
|||
|
|
5. Compile and flash the firmware: `make handwired/z150:default:flash`
|
|||
|
|
5. Align Black Pill pins B11–A4 with columns 0–7 and solder them.
|
|||
|
|
6. Connect rows, LEDs, ground and VCC traces to the corresponding pins of the BlackPill using additional wires.
|