First you will need a build a circuit to drive the solenoid through a mosfet as most MCU will not be able to provide the current needed to drive the coil in the solenoid.
|`SOLENOID_DEFAULT_DWELL` | `12` ms |Configures the default dwell time for the solenoid. |
|`SOLENOID_MIN_DWELL` | `4` ms |Sets the lower limit for the dwell. |
|`SOLENOID_MAX_DWELL` | `100` ms |Sets the upper limit for the dwell. |
|`SOLENOID_DWELL_STEP_SIZE` | `1` ms |The step size to use when `HPT_DWL*` keycodes are sent |
|`SOLENOID_DEFAULT_BUZZ` | `0` (disabled) |On HPT_RST buzz is set "on" if this is "1" |
|`SOLENOID_BUZZ_ACTUATED` | `SOLENOID_MIN_DWELL` |Actuated-time when the solenoid is in buzz mode |
|`SOLENOID_BUZZ_NONACTUATED` | `SOLENOID_MIN_DWELL` |Non-Actuated-time when the solenoid is in buzz mode |
* If solenoid buzz is off, then dwell time is how long the "plunger" stays activated. The dwell time changes how the solenoid sounds.
* If solenoid buzz is on, then dwell time sets the length of the buzz, while `SOLENOID_BUZZ_ACTUATED` and `SOLENOID_BUZZ_NONACTUATED` set the (non-)actuation times withing the buzz period.
* With the current implementation, for any of the above time settings, the precision of these settings may be affected by how fast the keyboard is able to scan the matrix.
Therefore, if the keyboards scanning routine is slow, it may be preferable to set `SOLENOID_DWELL_STEP_SIZE` to a value slightly smaller than the time it takes to scan the keyboard.
Beware that some pins may be powered during bootloader (ie. A13 on the STM32F303 chip) and will result in the solenoid kept in the on state through the whole flashing process. This may overheat and damage the solenoid. If you find that the pin the solenoid is connected to is triggering the solenoid during bootloader/DFU, select another pin.
### DRV2605L
DRV2605L is controlled over i2c protocol, and has to be connected to the SDA and SCL pins, these varies depending on the MCU in use.
#### Feedback motor setup
This driver supports 2 different feedback motors. Set the following in your `config.h` based on which motor you have selected.
##### ERM
Eccentric Rotating Mass vibration motors (ERM) is motor with a off-set weight attached so when drive signal is attached, the off-set weight spins and causes a sinusoidal wave that translate into vibrations.
#define FB_LOOPGAIN 1 /* For Low:0, Medium:1, High:2, Very High:3 */
/* Please refer to your datasheet for the optimal setting for your specific motor. */
#define RATED_VOLTAGE 3
#define V_PEAK 5
```
##### LRA
Linear resonant actuators (LRA, also know as a linear vibrator) works different from a ERM. A LRA has a weight and magnet suspended by springs and a voice coil. When the drive signal is applied, the weight would be vibrate on a single axis (side to side or up and down). Since the weight is attached to a spring, there is a resonance effect at a specific frequency. This frequency is where the LRA will operate the most efficiently. Refer to the motor's datasheet for the recommanded range for this frequency.
#define FB_LOOPGAIN 1 /* For Low:0, Medium:1, High:2, Very High:3 */
/* Please refer to your datasheet for the optimal setting for your specific motor. */
#define RATED_VOLTAGE 2
#define V_PEAK 2.8
#define V_RMS 2.0
#define V_PEAK 2.1
#define F_LRA 205 /* resonance freq */
```
#### DRV2605L waveform library
DRV2605L comes with preloaded library of various waveform sequences that can be called and played. If writing a macro, these waveforms can be played using `DRV_pulse(*sequence name or number*)`
List of waveform sequences from the datasheet:
|seq# | Sequence name |seq# | Sequence name |seq# |Sequence name |
This mode sets continuous haptic feedback with the option to increase or decrease strength.
## Haptic Key Exclusion
The Haptic Exclusion is implemented as `__attribute__((weak)) bool get_haptic_enabled_key(uint16_t keycode, keyrecord_t *record)` in haptic.c. This allows a re-definition at the required level with the specific requirement / exclusion.
*`LT()` layer tap keys, when held to activate a layer. However when tapped, and the key is quickly released, and sends a keycode, haptic feedback is still triggered.
*`TT()` layer tap toggle keys, when held to activate a layer. However when tapped `TAPPING_TOGGLE` times to permanently toggle the layer, on the last tap haptic feedback is still triggered.
*`MT()` mod tap keys, when held to keep a usual modifier key pressed. However when tapped, and the key is quickly released, and sends a keycode, haptic feedback is still triggered. See also [Mod-Tap](mod_tap.md).
With the entry of `#define NO_HAPTIC_ALPHA` in config.h, none of the alpha keys (A ... Z) will trigger a feedback.
### NO_HAPTIC_PUNCTUATION
With the entry of `#define NO_HAPTIC_PUNCTUATION` in config.h, none of the following keys will trigger a feedback: Enter, ESC, Backspace, Space, Minus, Equal, Left Bracket, Right Bracket, Backslash, Non-US Hash, Semicolon, Quote, Grave, Comma, Slash, Dot, Non-US Backslash.
### NO_HAPTIC_LOCKKEYS
With the entry of `#define NO_HAPTIC_LOCKKEYS` in config.h, none of the following keys will trigger a feedback: Caps Lock, Scroll Lock, Num Lock.
### NO_HAPTIC_NAV
With the entry of `#define NO_HAPTIC_NAV` in config.h, none of the following keys will trigger a feedback: Print Screen, Pause, Insert, Delete, Page Down, Page Up, Left Arrow, Up Arrow, Right Arrow, Down Arrow, End, Home.
