mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-11-23 08:56:47 +06:00
91 lines
2.0 KiB
Markdown
91 lines
2.0 KiB
Markdown
|
# DIP Switches
|
||
|
|
|
||
|
|
DIP switches are supported by adding this to your `rules.mk`:
|
||
|
|
|
||
|
|
DIP_SWITCH_ENABLE = yes
|
||
|
|
|
||
|
|
and this to your `config.h`:
|
||
|
|
|
||
|
|
```c
|
||
|
|
#define DIP_SWITCH_PINS { B14, A15, A10, B9 }
|
||
|
|
```
|
||
|
|
|
||
|
|
## Callbacks
|
||
|
|
|
||
|
|
The callback functions can be inserted into your `<keyboard>.c`:
|
||
|
|
|
||
|
|
```c
|
||
|
|
void dip_switch_update_kb(uint8_t index, bool active) {
|
||
|
|
dip_switch_update_user(index, active);
|
||
|
|
}
|
||
|
|
```
|
||
|
|
|
||
|
|
|
||
|
|
or `keymap.c`:
|
||
|
|
|
||
|
|
```c
|
||
|
|
void dip_switch_update_user(uint8_t index, bool active) {
|
||
|
|
switch (index) {
|
||
|
|
case 0:
|
||
|
|
if(active) { audio_on(); } else { audio_off(); }
|
||
|
|
break;
|
||
|
|
case 1:
|
||
|
|
if(active) { clicky_on(); } else { clicky_off(); }
|
||
|
|
break;
|
||
|
|
case 2:
|
||
|
|
if(active) { music_on(); } else { music_off(); }
|
||
|
|
break;
|
||
|
|
case 3:
|
||
|
|
if (active) {
|
||
|
|
#ifdef AUDIO_ENABLE
|
||
|
|
PLAY_SONG(plover_song);
|
||
|
|
#endif
|
||
|
|
layer_on(_PLOVER);
|
||
|
|
} else {
|
||
|
|
#ifdef AUDIO_ENABLE
|
||
|
|
PLAY_SONG(plover_gb_song);
|
||
|
|
#endif
|
||
|
|
layer_off(_PLOVER);
|
||
|
|
}
|
||
|
|
break;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
```
|
||
|
|
|
||
|
|
Additionally, we support bit mask functions which allow for more complex handling.
|
||
|
|
|
||
|
|
|
||
|
|
```c
|
||
|
|
void dip_switch_update_mask_kb(uint32_t state) {
|
||
|
|
dip_switch_update_mask_user(state);
|
||
|
|
}
|
||
|
|
```
|
||
|
|
|
||
|
|
|
||
|
|
or `keymap.c`:
|
||
|
|
|
||
|
|
```c
|
||
|
|
void dip_switch_update_mask_user(uint32_t state) {
|
||
|
|
if (state & (1UL<<0) && state & (1UL<<1)) {
|
||
|
|
layer_on(_ADJUST); // C on esc
|
||
|
|
} else {
|
||
|
|
layer_off(_ADJUST);
|
||
|
|
}
|
||
|
|
if (state & (1UL<<0)) {
|
||
|
|
layer_on(_TEST_A); // A on ESC
|
||
|
|
} else {
|
||
|
|
layer_off(_TEST_A);
|
||
|
|
}
|
||
|
|
if (state & (1UL<<1)) {
|
||
|
|
layer_on(_TEST_B); // B on esc
|
||
|
|
} else {
|
||
|
|
layer_off(_TEST_B);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
```
|
||
|
|
|
||
|
|
|
||
|
|
## Hardware
|
||
|
|
|
||
|
|
One side of the DIP switch should be wired directly to the pin on the MCU, and the other side to ground. It should not matter which side is connected to which, as it should be functionally the same.
|