mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-11-30 20:56:32 +06:00
99c6829bf0
Co-authored-by: Joel Challis <git@zvecr.com> Co-authored-by: Sergey Vlasov <sigprof@gmail.com> Co-authored-by: Drashna Jaelre <drashna@live.com>
54 lines
2.2 KiB
Markdown
54 lines
2.2 KiB
Markdown
# Polyandry/polypad
|
|
|
|
|
|
===
|
|
|
|
3x4/4x3 grid layout, multiple controllers supported
|
|
- Pro Micro
|
|
- PJRC Teensy 2.0
|
|
|
|
(**The below are not currently ported:**)
|
|
|
|
- PJRC Teensy LC/3.2
|
|
- PJRC Teensy 3.5/3.6
|
|
- Adafruit ItsyBitsy ATMega32u4
|
|
- Adafruit ItsyBitsy M0
|
|
- Adafruit ItsyBitsy M4
|
|
|
|
The matrix is electrically 1x12 with no diodes, with a thirteenth pin used for the column rather than a ground in order to be compatible with all the listed microcontrollers..
|
|
|
|
The default keymap is a testing keymap that is intended to make sure all of the keys on the matrix are working and properly assigned.
|
|
|
|
[The original (minimal arduino sketch) firmware, with support for some unsupported controllers](https://git.40percent.club/di0ib/Misc/src/branch/master/polyandry)
|
|
|
|
Keyboard Maintainer: QMK Community
|
|
Hardware Supported: Polyandry PCB
|
|
Hardware Availability: [Polyandry gerbers are on 40percent.club](https://www.40percent.club/2019/07/polyandry.html)
|
|
|
|
Make example for this keyboard (after setting up your build environment):
|
|
|
|
make 40percentclub/polyandry:default
|
|
or
|
|
qmk compile -kb 40percentclub/polyandry -km default
|
|
|
|
Default firmware is for an Arduino Pro Micro knockoff.
|
|
|
|
If you would like to specify a controller:
|
|
|
|
make 40percentclub/polyandry/promicro:default
|
|
or
|
|
qmk compile -kb 40percentclub/polyandry/promicro -km default
|
|
make 40percentclub/polyandry/teensy2:default
|
|
or
|
|
qmk compile -kb 40percentclub/polyandry/teensy2 -km default
|
|
|
|
## Bootloader
|
|
|
|
Enter the bootloader in 3 ways:
|
|
|
|
* **Bootmagic reset**: Hold down the top left key of the keyboard (top right or bottom left in horizontal configuration)
|
|
* **Physical reset**: Briefly press the button on the bottom of the microcontroller or, if not present short the pin marked RST to a GND.
|
|
* **Keycode in layout**: Press the key mapped to `RESET` if it is available
|
|
|
|
See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
|