keychron_qmk_firmware/keyboards/jd45/keymaps/mjt/rules.mk



# MCU name
#MCU = at90usb1287
MCU = atmega32u4

# Processor frequency.
#     This will define a symbol, F_CPU, in all source code files equal to the
#     processor frequency in Hz. You can then use this symbol in your source code to
#     calculate timings. Do NOT tack on a 'UL' at the end, this will be done
#     automatically to create a 32-bit value in your source code.
#
#     This will be an integer division of F_USB below, as it is sourced by
#     F_USB after it has run through any CPU prescalers. Note that this value
#     does not *change* the processor frequency - it should merely be updated to
#     reflect the processor speed set externally so that the code can use accurate
#     software delays.
F_CPU = 16000000


#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
ARCH = AVR8

# Input clock frequency.
#     This will define a symbol, F_USB, in all source code files equal to the
#     input clock frequency (before any prescaling is performed) in Hz. This value may
#     differ from F_CPU if prescaling is used on the latter, and is required as the
#     raw input clock is fed directly to the PLL sections of the AVR for high speed
#     clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
#     at the end, this will be done automatically to create a 32-bit value in your
#     source code.
#
#     If no clock division is performed on the input clock inside the AVR (via the
#     CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
F_USB = $(F_CPU)

# Interrupt driven control endpoint task(+60)
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT


# Boot Section Size in *bytes*
#   Teensy halfKay   512
#   Teensy++ halfKay 1024
#   Atmel DFU loader 4096
#   LUFA bootloader  4096
#   USBaspLoader     2048
OPT_DEFS += -DBOOTLOADER_SIZE=4096


# Build Options
#   comment out to disable the options.
#
BOOTMAGIC_ENABLE = yes	# Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes	# Mouse keys(+4700)
EXTRAKEY_ENABLE = yes	# Audio control and System control(+450)
CONSOLE_ENABLE = yes	# Console for debug(+400)
COMMAND_ENABLE = yes    # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no  # Breathing sleep LED during USB suspend
NKRO_ENABLE = yes		# USB Nkey Rollover - not yet supported in LUFA
BACKLIGHT_ENABLE = yes  # Enable keyboard backlight functionality
MIDI_ENABLE = no 		# MIDI controls
# UNICODE_ENABLE = YES 		# Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
Keymaps for several of my boards (#1641) * copied mjt keymaps from archive * All mjt boards now compile * fixed jd45-mjt breathing * Updates to fix SpaceFN but not tested yet. * Still missing either spacebar or an adjacent keypress. * Debugging rigged up for use with hid_listen. * Reverted the default keymap to use tap_layer_key rather than custom. Moved custom approach to keymap_debug.c * Fixed the lower-left side of the keymap, which needed more spacers due to the matrix being directly put into the array rather than using the keymap function. * Cleaned up JD45 keymap that uses tapkey. * Redid minivan keymap with numsym rather than raise/lower. Untested. * Created my MJT keymap for HHKB Enabled dynamic macros and moved somoe of the shortcuts around. * Minor keymap fixes to make them compile without errors. * Added home/end to right arrow cluster on DYN layer. * Added more keys to fn and dyn layers. * It wasn't using my custom layer last time somehow...? Now it will. * Compiled and installed at end of day on 8/23 * Moved macros to FKEY layer because Adjust was too hard to get into and out of without some sort of feedback. * Fixed volume controls... were reversed and disabled. * Added F13-F15 back to fkeys layer in Minivan * Created new Planck Keymap that uses the NumSym and FKeys layer approach like the Minivan. * Removed DYN layer. * Fixed diagram in planck numsym. * Cleanup for pull request. * Roadkit flip phone warning. * Replaced PLAY_NOTES_ARRAY to PLAY_SONG * reset the submodules * checked out specific commits for submodules * Removed debugging from JD45 shared config.h * Moved custom rules.mk to apropriate keymap Reset the shared rules.mk file. * Trailing return issue in rules.mk Gotta make for a smooth pull request :-) 2017-08-27 09:33:33 +06:00

			`# MCU name`
			`#MCU = at90usb1287`
			`MCU = atmega32u4`

			`# Processor frequency.`
			`# This will define a symbol, F_CPU, in all source code files equal to the`
			`# processor frequency in Hz. You can then use this symbol in your source code to`
			`# calculate timings. Do NOT tack on a 'UL' at the end, this will be done`
			`# automatically to create a 32-bit value in your source code.`
			`#`
			`# This will be an integer division of F_USB below, as it is sourced by`
			`# F_USB after it has run through any CPU prescalers. Note that this value`
			`# does not change the processor frequency - it should merely be updated to`
			`# reflect the processor speed set externally so that the code can use accurate`
			`# software delays.`
			`F_CPU = 16000000`


			`#`
			`# LUFA specific`
			`#`
			`# Target architecture (see library "Board Types" documentation).`
			`ARCH = AVR8`

			`# Input clock frequency.`
			`# This will define a symbol, F_USB, in all source code files equal to the`
			`# input clock frequency (before any prescaling is performed) in Hz. This value may`
			`# differ from F_CPU if prescaling is used on the latter, and is required as the`
			`# raw input clock is fed directly to the PLL sections of the AVR for high speed`
			`# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'`
			`# at the end, this will be done automatically to create a 32-bit value in your`
			`# source code.`
			`#`
			`# If no clock division is performed on the input clock inside the AVR (via the`
			`# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.`
			`F_USB = $(F_CPU)`

			`# Interrupt driven control endpoint task(+60)`
			`OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT`


			`# Boot Section Size in bytes`
			`# Teensy halfKay 512`
			`# Teensy++ halfKay 1024`
			`# Atmel DFU loader 4096`
			`# LUFA bootloader 4096`
			`# USBaspLoader 2048`
			`OPT_DEFS += -DBOOTLOADER_SIZE=4096`


			`# Build Options`
			`# comment out to disable the options.`
			`#`
			`BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)`
			`MOUSEKEY_ENABLE = yes # Mouse keys(+4700)`
			`EXTRAKEY_ENABLE = yes # Audio control and System control(+450)`
			`CONSOLE_ENABLE = yes # Console for debug(+400)`
			`COMMAND_ENABLE = yes # Commands for debug and configuration`
			`# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE`
			`SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend`
			`NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA`
			`BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality`
			`MIDI_ENABLE = no # MIDI controls`
			`# UNICODE_ENABLE = YES # Unicode`
			`BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID`