mirror of
https://github.com/Keychron/qmk_firmware.git
synced 2024-11-23 17:06:52 +06:00
83 lines
3.1 KiB
Makefile
83 lines
3.1 KiB
Makefile
|
#----------------------------------------------------------------------------
|
||
|
|
# On command line:
|
||
|
|
#
|
||
|
|
# make = Make software.
|
||
|
|
#
|
||
|
|
# make clean = Clean out built project files.
|
||
|
|
#
|
||
|
|
# That's pretty much all you need. To compile, always go make clean,
|
||
|
|
# followed by make.
|
||
|
|
#
|
||
|
|
# For advanced users only:
|
||
|
|
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
||
|
|
# (must have teensy_loader_cli installed).
|
||
|
|
#
|
||
|
|
#----------------------------------------------------------------------------
|
||
|
|
|
||
|
|
# # project specific files
|
||
|
|
SRC = matrix.c \
|
||
|
|
i2c_master.c \
|
||
|
|
left.c
|
||
|
|
|
||
|
|
# MCU name
|
||
|
|
MCU = atmega32u4
|
||
|
|
|
||
|
|
# Processor frequency.
|
||
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
||
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
||
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
||
|
|
# automatically to create a 32-bit value in your source code.
|
||
|
|
#
|
||
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
||
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
||
|
|
# does not *change* the processor frequency - it should merely be updated to
|
||
|
|
# reflect the processor speed set externally so that the code can use accurate
|
||
|
|
# software delays.
|
||
|
|
F_CPU = 16000000
|
||
|
|
|
||
|
|
#
|
||
|
|
# LUFA specific
|
||
|
|
#
|
||
|
|
# Target architecture (see library "Board Types" documentation).
|
||
|
|
ARCH = AVR8
|
||
|
|
|
||
|
|
# Input clock frequency.
|
||
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
||
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
||
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
||
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
||
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
||
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
||
|
|
# source code.
|
||
|
|
#
|
||
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
||
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
||
|
|
F_USB = $(F_CPU)
|
||
|
|
|
||
|
|
# Interrupt driven control endpoint task(+60)
|
||
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
||
|
|
|
||
|
|
# Boot Section
|
||
|
|
BOOTLOADER = atmel-dfu
|
||
|
|
|
||
|
|
# Build Options
|
||
|
|
# comment out to disable the options.
|
||
|
|
#
|
||
|
|
CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDone
|
||
|
|
UNICODE_ENABLE = yes # Unicode
|
||
|
|
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
||
|
|
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
||
|
|
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
||
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
||
|
|
COMMAND_ENABLE = no # Commands for debug and configuration
|
||
|
|
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
|
||
|
|
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
||
|
|
USB_6KRO_ENABLE = no # USB 6key Rollover
|
||
|
|
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
|
||
|
|
KEYMAP_SECTION_ENABLE = no # Fixed address keymap for keymap editor
|
||
|
|
SWAP_HANDS_ENABLE = no # Disable Onehand
|
||
|
|
RGBLIGHT_ENABLE = no
|
||
|
|
MIDI_ENABLE = no
|
||
|
|
|
||
|
|
LAYOUTS = ergodox
|